Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Coral Springs, FL
Gate installation in Coral Springs tends to split into two different jobs: replacing an aging aluminum driveway or pool gate from the 1980s on the older west side, or bringing an HOA entry gate up to current safety and access-control standards. Archway Gate Repair has served Coral Springs since 2011, and we work on the brands already installed across the city’s planned communities. If you need a new gate quoted, installed, and matched to your community’s design standards, call (855) 360-5306 for a free estimate.
Why Coral Springs Homes Are Different
Coral Springs is a master-planned city built almost entirely between 1963 and the 2000s, which means gate work here has two distinct eras. The older communities near Sample Road and University Drive hold original painted or powder-coated aluminum gates that have spent forty-plus years in South Florida humidity. Rust at the bottom rails, hinges that seize after rainy seasons, and latch posts that lean out of plumb are common. The newer developments east toward Turtle Run and the gated villages off Wiles Road use heavier ornamental steel and automated entry gates with safety loops, keypads, and vehicle detection sensors.
The practical difference is approvals. Nearly every gate in Coral Springs sits inside a deed-restricted HOA or gated village. A homeowner can’t simply swap a driveway gate for any style they like. The replacement must match community design standards, often requires architectural review, and sometimes needs the HOA’s own vendor approval. We quote with those constraints in mind from the first visit, so you don’t buy a gate your association will reject.
Climate matters too. Salt and wind-driven rain during hurricane season corrode steel and iron faster than inland Broward always gets credit for. Lightning from summer afternoon storms knocks out automated gate operators and safety sensors, and our repair calls in Coral Springs spike in July and August for exactly that reason.
Styles & brands we work with
Our Main Coral Springs Services
Most Coral Springs property owners call us for one of two reasons: a gate that won’t open or close properly, or an electric system that stopped responding entirely.
Gate Repair in Coral Springs
A sagging driveway gate, a pool gate that drags against the pavers, a latch that no longer catches: these are the mechanical failures we see most in Coral Springs, especially on older aluminum gates where the hinge posts have shifted over decades of heat and rain. We straighten, re-hang, rebuild hinge posts, replace rollers and latches, and repaint or touch up rust before it spreads. Repair first, replace only when necessary. For full details on mechanical gate work across Coral Springs, see our Gate Repair in Coral Springs page.
Electric Gate Repair in Coral Springs
When an automated gate stops midway, beeps without moving, or ignores the remote, the fault is usually in the control board, a limit switch, a safety loop, or the motor capacitor. Our electric gate repair in Coral Springs covers wiring, operators, photo eyes, keypads, and vehicle loops, and we see a lot of storm-related failures here from lightning and water intrusion at the operator housing. Diagnosed, not guessed. For the full scope of electrical and automation work, see our Electric Gate Repair in Coral Springs page.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Coral Springs
Gate installation in Coral Springs usually means one of two projects: replacing a rusted 1980s aluminum gate that no longer closes square, or installing a heavier automated gate at a newer home or HOA entry. We install manual and electric gates, built to survive South Florida humidity and matched to your community’s design rules. Whether it’s a full driveway gate, a sliding gate on a track, or an automated swing gate with safety sensors, Archway handles the entire job from the motor to the hinge. Read more about the scope on our Gate Installation page.
Automatic Gate Installation
Signs you need it
A manual gate that gets left open because no one wants to get out of the car, or an existing operator that’s failed more than twice in one year, points to a full automatic gate installation.
What it costs in Coral Springs
Automatic gate installation in Coral Springs typically falls between $3,300 and $11,900 depending on gate size, operator class, and whether new power and safety loops are required.
How we do it
We measure the opening, confirm swing or slide geometry, mount the gate and operator, run power and safety loops, program remotes and keypads, and test the full cycle with obstruction detection.
Driveway Gate Installation
Signs you need it
A driveway gate that’s rusted through at the bottom rail, sagging enough to scrape the concrete, or too narrow for modern vehicles is past repair and ready for replacement.
What it costs in Coral Springs
Driveway gate installation in Coral Springs generally runs $3,600 to $12,400, with single swing gates at the low end and long sliding gates or automated double gates at the high end.
How we do it
We remove the old gate and hardware, set or reinforce the posts, hang the new gate square, adjust the hinges and latch for the site’s slope, and walk you through the finish and operation.
What Gate Installation Costs in Coral Springs
| Item | Typical range in Coral Springs |
|---|---|
| Basic single manual gate | $3,300 – $5,400 |
| Automatic driveway gate (full system) | $3,300 – $11,900 |
| Sliding or double automated gate | $5,000 – $12,400 |
Do I need HOA approval to install a new gate in Coral Springs?
In most Coral Springs communities, yes. Nearly every neighborhood sits inside a deed-restricted HOA or gated village, and replacement gates must match community design standards. We can usually work from your HOA’s approved styles list if you provide it.
Does a new automatic gate in Coral Springs need safety sensors?
Yes. South Florida’s building code and UL 325 compliance require photo eyes and obstruction detection on automated gates, and your HOA may require additional safety loops. We install and test all sensors as part of every automatic gate installation.
Brands We Service in Coral Springs
Archway Gate Repair works on the operator already on your property, and in Coral Springs that often means a BFT or Viking on an HOA entry gate, a Linear on a 1990s residential swing, or a Ghost Controls opener on a newer home. We stock common control boards, remotes, loop detectors, and capacitors for these systems, so many Coral Springs repairs finish in one visit without waiting on parts. See the full list on our brands page.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Coral Springs, FL
| Service | Typical range in Coral Springs |
|---|---|
| Gate repair service call | $60 – $120 |
| Hinge replacement | $135 – $340 |
| Latch or lock repair | $95 – $280 |
| Operator board replacement | $460 – $1,100 |
| Electric gate repair | $145 – $640 |
| Automatic gate installation | $3,300 – $11,900 |
| Driveway gate installation | $3,600 – $12,400 |
| Sliding gate installation | $5,000 – $12,400 |
In Coral Springs, prices creep up when a job involves a long sliding gate, a storm-damaged control board with water intrusion, or an HOA entry gate that needs to stay operational during the repair. Every price is quoted and agreed before any work starts, so the number on the estimate is the number on the invoice.
Neighborhoods We Serve in Coral Springs
We work throughout Coral Springs and the surrounding communities. Response time for most repair calls in the area is same day or next morning, and installation quotes are usually scheduled within a few days.
- Maplewood
- Ramblewood
- Westchester
- Cypress Run
- Turtle Run
Service Area – Cities Near Coral Springs
Our Coral Springs team also covers nearby Broward communities. We regularly work in Parkland, FL, Tamarac, FL, Margate, FL, and North Lauderdale, FL, with the same brand-specific diagnostic approach on every gate.
Serving Coral Springs, FL — Our Local Coverage Area
We’re based in the Coral Springs area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Coral Springs
Most Coral Springs gate repairs can be scheduled same day or next morning, especially for a gate stuck open or a community entry gate that’s blocking vehicles. Call (855) 360-5306 and we’ll give you a realistic arrival window, not a vague promise.
We handle the technical side and provide drawings and specs for your HOA’s architectural review, but the application itself is typically filed by the homeowner or property manager. Most Coral Springs communities have a standard gate styles list we can work from.
We cover the full city, including all of ZIP code 33075, from the older central neighborhoods to the gated villages off Wiles Road and the communities near the Sawgrass Expressway. We also serve the bordering cities listed above.
If your gate needs work in Coral Springs, call (855) 360-5306 for a free estimate. We’ll tell you what’s wrong, what it costs, and whether repair or replacement makes more sense, before any work begins.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Coral Springs Customers Say
"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
— Ernesto Flores"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Roger Ziegler"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
— Tyrone Carter