Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Broadview Park
An electric gate that won’t open in Broadview Park isn’t a minor annoyance. It blocks your driveway, leaves deliveries stranded, and depending on the failure, can leave your property open overnight. Most electric gate repairs in Broadview Park run $180 to $480 for common fixes like control board replacement, sensor realignment, or hinge post resetting. We respond to Broadview Park calls within 24 to 48 hours in most cases, and we work on the brand already on your property. Call (855) 360-5306 and we’ll diagnose it over the phone before we even send a truck.
We know this area well. Broadview Park sits on low, sandy ground with a high water table, and that changes how gates fail here. What works in Plantation or Lauderhill doesn’t always translate to the 33317 ZIP. Nelson Arrieta built Archway Gate Repair as a gate-only shop precisely because electric gate problems in this pocket of Broward County have their own fingerprint. Standing water at post bases, salt air eating at control boards, and decades-old operators wired before modern safety standards existed. Those are the jobs we see every week.
Why Archway Gate Repair Is Broadview Park’s Preferred Electric Gate Repair Company
This isn’t a general handyman operation. We don’t do fences, we don’t do garage doors, we don’t pick up side work. Every job we take in Broadview Park is a gate job. That single-specialty focus means our technicians have seen the specific failure patterns of LiftMaster, FAAC, BFT, DoorKing, Linear, Viking, Ghost Controls, Elite, and Mighty Mule systems hundreds of times before they arrive at your driveway. Diagnosed, not guessed.
Broadview Park homeowners and property managers call us because the person on the phone understands what a “loop detector fault” or “errant photocell” actually means. We’re not reading from a script. Nelson Arrieta leads a team that repairs electric gates from the motor to the hinge, and we carry parts for the operators most common across 1950s to 1970s Broward County homes. That means fewer second trips and fewer days waiting on a FedEx box. When your gate is stuck open at 8 p.m., that matters.
Our reputation in Broadview Park is built on repair-first honesty. If a $160 hinge repair buys you five more years, we’ll tell you that instead of quoting a $3,000 replacement. That’s why property managers along State Road 7 and homeowners off Davie Road Extension keep our number in their phones.
Styles & brands we work with
Gate Access Control in Broadview Park
Gate Access Control in Broadview Park usually means upgrading an older swinging or sliding gate so it opens only for authorized people. That can involve keypads, remotes, intercom systems, phone-based entry, or full vehicle detection loops. Many Broadview Park homes built in the 1960s and 1970s still have the original gate hardware, and access control was often added years later as an afterthought. We bring those systems up to a standard that actually works daily in South Florida weather.
Retrofitting Older Gates
A surprising number of Broadview Park properties have operators wired without modern entrapment protection. Retrofitting usually costs $350 to $900 depending on whether we’re adding photocells, safety edges, or replacing an obsolete control board. The goal is a gate that meets current UL 325 standards without replacing the entire system.
Keypads and Remote Systems
Salt-laden air from the nearby coast corrodes keypad contacts and remote receiver boards faster than you’d expect. If your keypad works intermittently or only from two feet away, the fix is often a receiver swap and sealed keypad replacement. We stock parts locally for Broadview Park customers, so most access control repairs happen in one visit.
Commercial Gate Operator in Broadview Park
Commercial Gate Operator service in Broadview Park covers the heavier slide and swing operators used at apartment complexes, small storage facilities, and business lots along State Road 7. These operators run more cycles in a week than a residential gate runs in a year, and the salt air plus sandy soil adds extra stress. We work on commercial operators from BFT, Viking, and Linear, among others, because those are the brands installed across Broward County commercial properties.
Slide Gate Operators
Slide gates in Broadview Park fight two local enemies: corrosion on the rack and pinion, and ground shift that throws the track out of level. When the gate starts jerking or reversing mid-cycle, we check the rack for salt corrosion first. Track resets and rack replacements for commercial slide operators generally run $600 to $1,800 depending on gate weight and run length.
Swing Gate Operators
Commercial swing operators on sandy lots see post movement over time, especially after a wet season. The repair often means pulling the post, resetting it in concrete with deeper footings, and then recalibrating the operator. This isn’t a job for a generalist. We handle the full scope: power run verification, limit switch setup, safety loop installation, and final torque checks.
Trusted Brands We Service in Broadview Park
We work on the brand already on your property. Archway Gate Repair’s technicians are factory-familiar with nine of the most widely installed gate systems in Broadview Park, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Brand-specific knowledge means faster diagnosis. A Ghost Controls swing arm has different failure points than a Viking slide operator, and we know both before we open the cover. For Broadview Park customers, we keep common parts staged locally so repairs move quickly.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Broadview Park Homes
- Obsolete control boards dying from humidity and salt air. Older operators, especially those installed before 2005, have boards that corrode at the solder joints. The gate usually behaves erratically first, then stops responding altogether.
- Posts shifting in waterlogged sand. Broadview Park’s high water table means gate posts often sit in standing water after afternoon thunderstorms. The post shifts, the gate sags, and the operator strains against a gate that no longer hangs plumb.
- Corroded hinges and rack-and-pinion hardware. Salt-laden air from the coast makes metal components rust faster here than in inland Broward cities. Hinges bind, chains stretch, and slide gate racks lose teeth.
- Loop detectors failing after heavy rain. Driveway loops buried in sandy, shifting soil crack or short out when water pools. The gate won’t open for cars but opens for the remote, which confuses a lot of homeowners.
Pricing for Electric Gate Repair in Broadview Park, FL
We quote the price before any work starts, and the number we agree on is the number you pay. A typical control board replacement in Broadview Park runs $280 to $520 depending on the brand. Hinge post resetting, common in this area because of the sandy soil, runs $220 to $450 per post including concrete. Safety sensor repair or replacement runs $160 to $340. Full operator retrofits with photocells and a modern board run $750 to $1,800. Every estimate is free. Call (855) 360-5306 and we’ll give you a written number before a single part gets ordered.
We Also Serve Cities Near Broadview Park
Beyond Broadview Park, our Electric Gate Repair team regularly handles calls in Fort Lauderdale, Plantation, Broward Estates, and Lauderhill. If you manage properties across multiple Broward County cities, one call covers the whole spread. Same team, same gate-only focus, same repair-first approach.
Serving Broadview Park, FL — Our Local Coverage Area
We’re based in the Broadview Park area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Broadview Park
The most common cause is a failing loop detector or a shorted wire in the safety circuit. In Broadview Park, buried loop wires crack when sandy soil shifts, and heavy rain completes the short. A corroded control board can also send phantom open signals. We diagnose it with a multimeter and replace only what’s actually failed. Call (855) 360-5306 for a free estimate.
Yes. Most pre-2010 operators can accept aftermarket photocells and safety edges if the control board supports them. If the board is too old, we replace the board with a modern equivalent from the same brand and add the sensors at the same time. Retrofit work in Broadview Park typically runs $350 to $900. We quote it upfront before any work begins.
The high water table and sandy soil mean water collects at the base of gate posts after every afternoon storm. The soil loses bearing capacity, the post shifts, and the gate sags. In drier inland cities, posts stay seated for decades. Here, resetting posts in concrete with deeper footings is a routine repair, not an unusual one. We’ve done so many post resets in the 33317 ZIP that it’s often the first thing we check on a sagging gate.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. We don’t push you toward a specific brand. We repair the one already bolted to your property. Call (855) 360-5306 and tell us what’s on the motor cover; we’ll likely know the failure before we hang up.
It depends on the failure. If the motor is fine and the board failed, replacing the board for $280 to $520 makes sense. If the motor bearings are screaming and the board is obsolete, replacement is cheaper long-term. We’ll show you both numbers and let you decide. We’d rather lose a replacement sale than sell you something you didn’t need. Call (855) 360-5306 for an honest read on the gate you have.
Written by Nelson Arrieta, Owner at Archway Gate Repair, serving Broadview Park and surrounding Broward County communities.