Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Tavernier
Gate repair in Tavernier usually runs $185 to $485 depending on whether the issue is a misaligned hinge, a corroded control board, or a motor that’s given up entirely. We’re a gate-only specialist, not a handyman with a truck, and our techs know Tavernier’s salt-air failure patterns before they even roll up the driveway. Whether you’re on the Florida Bay side of US-1 or tucked off the oceanside stretch near Tavernier Creek, call (855) 360-5306 and we’ll have someone out to diagnose the problem, not guess at it.
Why Archway Gate Repair Is Tavernier’s Preferred Gate Repair Company
Tavernier presents a specific challenge: the same LiftMaster or FAAC operator that runs flawlessly in Homestead for a decade can fail here in three or four years because every lot sits within salt-spray distance of tidal water. Nelson Arrieta built Archway Gate Repair around that reality. We work on the brand already on your property, we know which components fail first in this climate, and we stock marine-grade replacement hardware because painted steel simply doesn’t survive long on a bayfront gate post.
Our techs know the 33070 zip code well. We understand that gated driveways off Burton Drive and the stilt homes along Old State Road 4A have concrete pier footings, not deep-soil posts, and that changes how we approach a gate realignment. When a Tavernier customer calls about a gate that won’t cycle after a storm, our first question isn’t “what brand is it?” It’s “which side of the highway are you on?” Because it matters. Response time to Tavernier is typically same day for emergency calls, and every quote is agreed before we touch a single bolt.
Styles & brands we work with
Commercial Gate Repair in Tavernier
Commercial Gate Repair in Tavernier covers the HOA entrances, marina access gates, and small business driveways that run on DoorKing, BFT, and LiftMaster operators, most of which are now reaching the age where salt corrosion has worked its way into the control box and photo-eye wiring. These systems cycle dozens of times a day, and in Tavernier’s humidity a low-mounted control enclosure becomes a corrosion chamber within a couple of seasons. We don’t just swap the board; we relocate or reseal the enclosure, replace corroded terminal strips, and re-run low-voltage wiring with sealed connectors so the next storm season doesn’t put you back in the same spot.
Access Control and Safety Loop Repair
Commercial gates in Tavernier often rely on in-ground safety loops, and those loops fail quietly. Crushed-shell and paver driveways shift, saltwater intrusion corrodes the loop wire, and the operator starts refusing to close. We troubleshoot the loop detector, locate the break, and splice in marine-rated wire where needed. It’s a repair, not a full replacement, and it keeps your gate legal and operational.
Operator and Motor Service for Tavernier Businesses
A commercial operator that’s been exposed to wind-driven rain for three hurricane seasons rarely needs a full replacement. More often it needs the capacitor or limit switches replaced, the housing resealed, and the safety edges re-tested. We quote repair before replacement, and commercial pricing in Tavernier typically runs $325 to $900 depending on parts and whether we’re re-terminating existing wiring.
Iron Gate Repair in Tavernier
Iron Gate Repair in Tavernier almost always comes down to corrosion management. The ornamental iron gates on canal-front concrete-block homes and elevated stilt houses look beautiful for the first two years, and then the salt-laden onshore breeze starts eating the paint at every welded joint. We see bayside gates with the windward hinge post pitted through while the rest of the gate looks acceptable. The fix isn’t just repainting; it’s grinding out the rust, welding in replacement sections where the metal has thinned, and re-finishing with a marine-grade primer and epoxy paint that’s actually spec’d for coastal exposure.
Hinge and Post Rebuilding
When a Tavernier iron gate starts dragging or sagging, the hinge post is usually the culprit. On larger oceanside lots the gate mounts to a coral-rock-based footing, which means the post can’t be replaced like it would be in soil. We sleeve and rebuild in place, weld new hinge plates onto the existing steel, and re-hang the gate so it swings clean. That’s often a $250 to $550 repair and it buys years of service without touching the footing.
Weld and Rust Repair
Weld failures on Tavernier iron gates happen at the picket-to-rail joints and the hinge barrels, exactly where water sits. We grind the failed weld, re-weld with stainless or zinc-rich filler, and coat the repair so it doesn’t become the next failure point. If the gate is heavily pitted on one face, we’ll tell you honestly whether it’s worth salvaging or whether a new gate is the smarter spend.
Trusted Brands We Service in Tavernier
Archway Gate Repair is factory-familiar with the brands already installed across Tavernier: LiftMaster, FAAC, Elite, Mighty Mule, BFT, Linear, Viking, Ghost Controls, and DoorKing. That brand knowledge means faster diagnosis. A Mighty Mule that won’t respond to the remote is a different problem than a FAAC that faults after rain, and we know which is which before we open the housing. We keep common replacement parts and marine-grade hardware stocked locally so Tavernier customers aren’t waiting a week for a hinge or a control board. Diagnosed, not guessed. From the motor to the hinge, we cover the whole gate system.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Tavernier Homes
- Windward-face corrosion on bayside gates. Homes on the Florida Bay side of US-1 get persistent onshore breeze, and the hinge post and gate face facing the water pit and rust years before the leeward side. Galvanised or stainless hardware is the only spec that holds up.
- Flooded control enclosures after wind-driven rain. Low-mounted operator boxes fill with water during a summer squall and the board shorts. We re-seal and often re-mount the enclosure higher or install a sealed NEMA box.
- Phantom obstruction faults after tropical systems. After a June or September storm, gates that aren’t broken at all refuse to cycle because a photo-eye bracket shifted a quarter inch or the safety loop flooded. The first visit is often drying out and re-aligning, not replacing the motor.
- Concrete pier and coral-rock footing complications. Older Tavernier homes built from the 1960s through the 2000s often have gates bolted to concrete piers or coral-rock, not buried posts. Any hinge or post repair has to work around that footing, and we do it without jackhammering your driveway.
Pricing for Gate Repair in Tavernier, FL
Gate repair in Tavernier typically falls into clear ranges. Mechanical work, like hinge replacement or gate realignment, runs $185 to $400. Electrical diagnosis and repair on an automatic gate operator, including control board replacement or limit switch work, runs $275 to $650. Full motor or operator replacement can push $850 to $1,400 depending on the brand and whether we’re also replacing the safety edges and photocells. Commercial jobs trend higher because of the heavier cycles and added safety requirements. Every customer gets a written price agreed before work starts, and estimates are free. Call (855) 360-5306 for an exact quote on your gate.
We Also Serve Cities Near Tavernier
Our Gate Repair crew regularly works up and down the Keys. Beyond Tavernier, we cover Key Largo, North Key Largo, Islamorada, and Florida City with the same brand-specific service and marine-grade hardware spec. If your gate sits within salt-spray distance of the water in any of those communities, we know exactly what fails first there, too.
Serving Tavernier, FL — Our Local Coverage Area
We’re based in the Tavernier area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Tavernier
Because Tavernier sits on a narrow strip of Key Largo where every property line runs from US-1 bayfront to oceanside, so the gate operator is exposed to salt-laden onshore air on at least one side, year-round. The control board, terminal strips, and low-voltage wiring in a standard enclosure will start corroding within two to three seasons. We spec elevated, sealed enclosures and marine-grade connectors as default here, not as an upgrade. If your operator is acting up, call (855) 360-5306 and we’ll assess whether it’s a board failing from corrosion or something simpler.
In Tavernier, the most common post-storm issue is a shifted photo-eye bracket or a flooded safety loop, not a dead motor. The wind flexes the gate enough to move the photocell a quarter inch, and the operator reads that as an obstruction and refuses to cycle. We see it after almost every tropical system. We dry out and reseal the loop enclosure, re-align the photo-eye, and re-torque the hinge bolts, then run a full cycle test. If that gets your gate moving again, you avoided a motor replacement. Call (855) 360-5306 to schedule a post-storm check.
Galvanised. Painted steel hinge posts on bayfront-facing gates in Tavernier pit and fail within a few seasons because the onshore breeze attacks the windward face first. We regularly replace painted posts that have thinned to the point of flexing under the gate’s weight. Galvanised or stainless-spec steel holds up dramatically better, and for welded repairs we use zinc-rich or stainless filler so the repair doesn’t become the next rust point. If your post is showing rust blisters, call (855) 360-5306 for an assessment before it fails outright.
Older Tavernier homes, especially the concrete-block canal-front houses and stilt homes built from the 1960s onward, often have gates bolted to concrete piers or coral-rock-based footings rather than posts set in soil. That means you can’t dig out and replace a failed post the way you would inland. We sleeve and rebuild the post in place, weld new hinge plates to the existing steel, and re-hang the gate without touching the footing. It’s more involved, but it preserves the original structure and usually runs $250 to $550. Call (855) 360-5306 and we’ll tell you exactly what your footing allows.
Yes. Automatic gates in Tavernier, as everywhere in Florida, must have functioning entrapment protection: photo-eyes, safety edges, or both, depending on the installation. On a coastal property those sensors fail faster than the motor because they sit low and take salt spray directly. We test entrapment protection on every automatic gate repair visit and replace sensors with sealed marine-rated units when they’ve failed. A gate that reverses properly is a legal gate. Call (855) 360-5306 to have yours tested.
We were called to a stilt home off the oceanside stretch near Tavernier Creek where a LiftMaster swing gate operator kept throwing phantom obstruction faults after a June storm. The safety photocell bracket had shifted a quarter inch and the loop detector in the crushed-shell driveway had taken on water. Our tech dried and resealed the enclosure, realigned the photo-eye, and re-torqued the stainless hinge bolts on the corroded hinge post rather than replacing the motor. The gate has run clean since, and we scheduled a post-storm alignment check for the rest of hurricane season.
Written by Nelson Arrieta, Owner at Archway Gate Repair, serving Tavernier and the Upper Keys.