Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Broadview Park
Gate repair in Broadview Park usually means one of two things: either a decorative aluminum gate that has finally sagged off its hinges after fifty years of subtropical weather, or an electric operator at a rural entrance that won’t respond because the post its mounted on has shifted in sandy, waterlogged soil. We handle both. Archway Gate Repair works on the brand already on your property, from a Mighty Mule swing opener on a duplex driveway to a heavy BFT slide operator at an acreage entrance off SW 18th Street. Call (855) 360-5306 and Nelson Arrieta’s team will diagnose the problem before quoting a fix. We live in this soil. We know why gates fail here.
Why Archway Gate Repair Is Broadview Park’s Preferred Gate Repair Company
Broadview Park is not like inland Broward. The water table sits close to the surface, the air carries salt from the coast, and afternoon thunderstorms leave water standing around post footings all summer. A general handyman might tighten hinges and call it done; we know to check whether the post itself is still straight in the ground before touching the hardware. That local read saves Broadview Park homeowners from paying for a repair that fails in six months.
Our Gate Repair team arrives with diagnostic equipment for both mechanical and electrical failures, so we don’t guess. If the operator is dead, we test the board, the motor, and the power feed separately. If the gate drags, we check the track, the rollers, and the footing. Customers across Broadview Park tell us the same thing: the repair held. That’s the standard.
We’re also familiar with every gate style in this area, from original 1960s chain-link fencing to modern aluminum driveway gates on newer duplexes. The housing stock in Broadview Park is mostly 1950s to 1970s CBS ranch homes and small multi-family buildings. Most gates were installed with the house and have never been rebuilt. We know how those old installations fail and what it takes to make them work again without replacing everything.
Styles & brands we work with
Iron Gate Repair in Broadview Park
Iron gate repair in Broadview Park typically means addressing rust, broken welds, sagging hinges, or a post that has shifted in saturated soil. A straightforward hinge-and-weld repair on an iron gate here runs $280 – $520. If the post has moved and needs to be reset in concrete, the job usually runs $450 – $900 depending on how much of the footing has to be excavated and whether the gate must be lifted off and re-hung.
What we see most often on original iron gates in Broadview Park is rust at the bottom rail, where standing water splashes up and sits against the steel. The gate still looks fine from the driveway, but the lower rail is thinning from the inside. We cut out the rotted section, weld in new steel, and coat the repair so it doesn’t bloom again in the humid season.
Weld and Rust Repair
Steel gates in Broadview Park take a beating from salt air and regular thunderstorms. When we weld a gate, we grind the area clean first, then paint or coat it to slow future corrosion. On older iron gates, we check the entire frame for weak points, because a gate that failed in one spot usually has two or three other spots ready to go.
Hinge and Post Reset
An iron gate that drags or won’t latch is often the victim of a post that has tilted in water-softened ground. We reset the post in fresh concrete and brace it level before re-hanging the gate. If the hinge pins are worn, we replace them at the same time so the gate swings clean for years.
Sliding Gate Repair in Broadview Park
Sliding gate repair in Broadview Park frequently involves track and roller problems caused by sandy soil washing onto the track bed and binding the gate. A basic roller and track cleanup runs $250 – $450. If the rack and pinion gear is stripped or the gate has jumped the track, the repair typically runs $500 – $950, including re-aligning the gate and testing the motor under load.
Wide farm and acreage entrances around Broadview Park use heavier slide gates than what you’ll find at a typical suburban driveway. Those gates put real stress on the operator and the track, especially when the post footing shifts after heavy rain. We diagnose, not guess. If the motor is overheating, we measure the amp draw before deciding whether it’s the motor, the track, or a failing battery on a solar system.
Roller and Rack Alignment
Slide gates need to roll true or every component works harder than it should. We set the rollers so the gate moves freely across the full travel, then align the rack with the drive gear. A gate that’s binding at one end only often has a footing issue at that end, not a bad motor.
Heavy-Duty Operator Service
For wide gates, the operator must be rated for the gate’s full weight and cycle count. When an operator fails at a Broadview Park acreage entrance, we check whether the original unit was undersized from the start. If it was, we recommend a properly rated replacement from a brand like BFT or Viking rather than another failed swap of the same weak model.
Trusted Brands We Service in Broadview Park
We work on the brand already on your property. That means Ghost Controls swing openers on small residential gates, Linear slide operators on commercial entrances, Viking and BFT units on rural acreage gates, and everything in between. We stock common parts locally so Broadview Park customers aren’t waiting on a two-week shipment for a control board or a set of photo eyes. Because our technicians are factory-familiar with these systems, we arrive knowing the typical failure points for each brand and where to start the diagnostic. That’s faster for you and cheaper in labor time. We’re also comfortable working on solar-powered operators, which are common on Broadview Park properties where running mains power to a rural gate is impractical.
Common Gate Repair Problems We See in Broadview Park Homes
- Post shift from standing water. Afternoon thunderstorms saturate the sandy soil around post footings, and over time the post leans or sinks. A gate that dragged after last summer’s rains usually needs a concrete reset, not just a hinge adjustment.
- Corroded hardware from salt air. Even two or three miles from the coast, Broadview Park gets enough salt in the air to eat hinges, tracks, and operator housings faster than inland Broward. We replace with coated or galvanized hardware where we can.
- Solar operator battery failure. Solar gate openers depend on the battery to run the motor, and Florida’s cloudy summer weeks can outpace a small panel. We test the battery’s actual capacity and the panel’s output before replacing either.
- Eroded wiring from sandy soil. Buried low-voltage wire to keypads and safety loops gets exposed and worn by shifting sand. If the gate works but the keypad is dead, we trace the wire path before condemning the opener.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Broadview Park, FL
Gate repair in Broadview Park runs from about $220 for a minor hinge or latch fix up to $950+ for a full post reset and operator replacement on a heavy slide gate. Here’s what to expect:
- Hinge, latch, or minor alignment work: $220 – $400
- Weld repair and rust remediation: $280 – $520
- Roller and track repair on a sliding gate: $250 – $450
- Post reset in concrete: $450 – $900
- Rack and pinion replacement with operator testing: $500 – $950
- Electric operator replacement with safety sensor check: $850 – $1,800
The price you’re quoted is the price you pay, and we agree on it before any work starts. We don’t surprise anyone with an invoice that’s bigger than the estimate. Call (855) 360-5306 and we’ll come out, look at the gate, and give you a written number. Estimates are free.
We Also Serve Cities Near Broadview Park
If you’re on the edge of Broadview Park or managing properties in the neighboring area, we also cover Gate Repair in Broadview Park and the surrounding communities including Fort Lauderdale, Plantation, Broward Estates, and Lauderhill. The same team, the same brand knowledge, and the same repair-first approach, wherever your gate happens to be.
Serving Broadview Park, FL — Our Local Coverage Area
We’re based in the Broadview Park area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Broadview Park
Broadview Park sits on a high water table with sandy soil, so post footings stay wet for days after each afternoon thunderstorm. The saturated soil loses its grip on the concrete footer, and the post slowly leans or sinks. In drier inland areas, a post might stay put for decades. Here, it’s common for a 20-year-old gate post to need a reset, especially on original 1960s and 1970s installations. A reset in fresh concrete, with proper drainage around the base, solves the problem at the source instead of repeatedly re-shimming the hinges. Call (855) 360-5306 if your gate is dragging or leaning, and we’ll tell you honestly whether the post is the issue.
Yes, but only if the panel and battery are sized for the gate’s actual weight and daily cycle count. A wide farm gate needs a heavier-duty operator, and a small solar panel won’t keep up during Florida’s cloudy stretches. We recently repaired a wide farm gate off SW 18th Street in Broadview Park where the homeowner had a LiftMaster solar opener on a heavy-duty slide gate, but the post footing had shifted due to standing water, causing the rack and pinion to bind. We reset the hinge post in fresh concrete, replaced the corroded operator, and added a safety photocell to meet UL 325, restoring reliable access. The solar was fine; the problem was the footing and the undersized battery. We test the full system before swapping parts.
Automatic gates in Broadview Park must comply with UL 325, which requires safety devices to prevent entrapment. That means photo eyes or safety edges that detect an obstruction and stop or reverse the gate, plus proper warning signage. If you have an older system without these devices, or if the sensors have failed, we can bring the gate up to code during the repair. This isn’t optional paperwork; a gate that closes on a vehicle, a child, or an animal is a serious liability. We install and test safety devices on every automatic gate repair we do.
It’s most often the track, the rollers, or a shifted post in Broadview Park, not the motor. Sandy soil washes onto the track and grinds into the rollers, and standing water corrodes the track surface. If the post has shifted even half an inch, the rack and pinion bind and the motor works against the resistance until it overheats or burns out. We check the gate’s movement by hand first, because a gate that’s hard to push will kill any operator we install. That’s the difference between diagnosing and guessing. Call (855) 360-5306 and we’ll figure out which part of the system actually failed before quoting a fix.
The sandy, waterlogged soil in Broadview Park erodes buried wiring and makes concrete footings less stable than they are on higher ground. For operator installation, we dig a deeper footing than you’d use inland and use concrete with proper drainage so water doesn’t pool at the base. For buried wire, we run it in conduit wherever possible, because shifting sand exposes direct-buried cable surprisingly fast. These aren’t things you notice on an invoice, but they’re the difference between an operator that lasts ten years and one that fails after two. Our approach is repair first, replace only when necessary, and install it to handle Broadview Park’s actual conditions.
Call Archway Gate Repair for Gate Repair in Broadview Park
If your gate is sagging, dragging, stuck open, or dead, don’t wait for the next thunderstorm to make it worse. Nelson Arrieta and the team at Archway Gate Repair work on the brand already on your property, diagnose before we quote, and fix the problem at the source. From the motor to the hinge, we handle the whole system, and we stand behind the work. Call (855) 360-5306 for a free estimate in Broadview Park. We’ll come out, look at the gate, and tell you exactly what it needs.
Written by Nelson Arrieta, Owner at Archway Gate Repair, serving Broadview Park and all of Broward County.